瀝青路面面層厚度不足，在行車荷載作用下出現結構性裂縫。半剛性基層收縮裂縫產生的反射裂縫。橋、涵洞兩側路堤填土沉降，導致裂。瀝青是不同分子量的碳?xì)浠衔锖秃诤稚墙饘傺苌锏膹?fù)雜混合物，是一種高粘度有機液體，液態，黑色表面，可溶于 。瀝青是一種防水防潮防腐的有機膠凝材料。

Insufficient thickness of asphalt pavement surface layer leads to structural cracks under driving loads. Reflection cracks caused by shrinkage cracks in semi-rigid base layers. The settlement of the embankment filling on both sides of the bridge and culvert leads to cracks. Asphalt is a complex mixture of hydrocarbons with different molecular weights and black brown non-metallic derivatives. It is a high viscosity organic liquid, liquid, black surface, and soluble. Asphalt is an organic binder material that is waterproof, moisture-proof, and corrosion-resistant.

經過多年來的不斷和完善，冷補料材料的性能更加成熟。無論在和使用上，都優于熱拌的瀝青、乳化瀝青混合料，并以其操作簡單、存放長久、修補好、用途廣泛、利于環保的特點，已在全應用，在國內許多市政道路、一般公路、高速公路推廣應用。

After years of continuous improvement, the performance of cold repair materials has become more mature. Both in terms of operation and use, it is superior to hot mix asphalt and emulsified asphalt mixtures. With its characteristics of simple operation, long-term storage, good repair, wide use, and environmental friendliness, it has been widely applied and promoted in many municipal roads, general highways, and expressways in China.

㎡）（高速公路及車流量大的交通路段修補時必須涂刷界面劑）

㎡ (Interface agent must be applied when repairing highways and traffic sections with high traffic volume)

填滿坑槽

Fill the pit and groove

把足夠的冷補材料填進坑槽內，直到填料高出路面l.5cm左右，填滿后坑槽處應稍高于四周路面并呈弧形，若路面坑槽深度大于5cm時，應分層填補，逐層壓實，每層3—5cm。

Fill enough cold filling material into the pit until the filling is about 1.5cm higher than the road surface. After filling, the pit should be slightly higher than the surrounding road surface and form an arc. If the depth of the road pit is greater than 5cm, it should be filled layer by layer, compacted layer by layer, and each layer should be 3-5cm.

壓實

compaction

鋪設均勻后，根據實地環境，修補面積的大小和深度，選擇適當?shù)膲簩?shí)工具和方法進行壓實。如汽車輪胎壓實、人力夯（hang）、振動平板夯壓實、壓路機壓實。高等級公路修補時，修補區域的四周和邊角應保證充分地壓實。

After laying evenly, select appropriate compaction tools and methods based on the on-site environment, the size and depth of the repair area, and carry out compaction. Such as car tire compaction, manual compaction (hang), vibrating flat compactor compaction, and roller compaction. When repairing high-grade highways, the edges and corners of the repaired area should be fully compacted.

通車

Open to traffic

修補完的坑槽表面應光潔、平整、無輪跡，坑槽四周邊角一定要壓實，無松散現象。普通道路修補壓實度要達到93％以上，高速路修補壓實度要達到95％以上。

The surface of the repaired pit should be smooth, flat, and free of wheel marks. The edges and corners of the pit must be compacted without any looseness. The compaction degree of ordinary road repair should reach over 93%, and the compaction degree of highway repair should reach over 95%.

本文由濟南瀝青料友情奉獻.更多有關的知識請點擊:http://id888.com.cn真誠的態度.為您提供為全面的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.

This article is dedicated by Jinan Asphalt Materials. For more information, please click: http://id888.com.cn Sincere attitude. We will provide you with comprehensive service. We will gradually contribute more relevant knowledge to everyone. Stay tuned