公司新聞
裝載機租賃維修有四大問題要了解
來源：http://id888.com.cn/ 日期：2022-04-27
裝載機是一種大型施工設備，應用環境不是那么好，所以使用時間長了就會導致故障的出現，這時就要進行維修，那么下面我們就來說說裝載機租賃維修有哪些問題要了解吧。
The loader is a kind of large construction equipment, the application environment is not so good, so the use of a long time will lead to failure, then it is necessary to carry out maintenance, so let's say what problems there are to understand the loader rental maintenance.
裝載機工作正常，油溫高，輸出功率不足，傳動液中有泡沫鋁？ 回油濾清器堵塞，機械機油散熱器堵塞，回油管路不暢，軸承損壞，變矩器三輪磨損。 清洗濾芯或更換濾芯，更換散熱器，清洗疏通各油路，更換軸承，更換三輪并調整間隙。
The loader works normally, the oil temperature is high, the output power is insufficient, and there is aluminum foam in the transmission fluid. The return oil filter is blocked, the mechanical oil radiator is blocked, the return oil pipeline is not smooth, the bearing is damaged, and the torque converter three wheels are worn. Clean the filter element or replace the filter element, replace the radiator, clean and dredge the oil, replace the bearing, replace the three wheels and adjust the clearance.
低速或高速脫離怎么辦？ 控制部分間隙過大或拉桿調整不當，滑套與高低速齒輪磨損，嚙合量過小，高低速齒輪襯套與輸出間隙 軸過大，貨叉變形或貨叉軸定位彈簧折斷。 調整各相關拉桿間隙，更換損壞的滑套和齒輪，更換齒輪襯套并調整間隙，更換或修理前叉，更換彈簧。
What about low or high speed detachments? Control part clearance is too large or the pull rod is improperly adjusted, sliding sleeve and high and low speed gear wear, meshing is too small, high and low speed gear bushing and output clearance shaft is too large, fork deformation or fork shaft positioning spring broken. Adjust the clearance of the relevant pull rod, replace the damaged sliding sleeve and gear, replace the gear bushing and adjust the clearance, replace or repair the front fork, replace the spring.
行車時剎車踏板踩到底，剎車突然失靈？ 濟南裝載機租賃人員認為，原因是加力主缸密封圈損壞或翻倒，加力主缸內沒有制動液，沒有制動氣壓，制動管路嚴重破裂或管路 接頭斷開。 更換損壞的密封圈，加足制動液至標準值，排掉油路中的空氣，更換損壞的制動管路。
Hit the brake pedal to the bottom and the brake suddenly fails? Ji 'nan loader leasing personnel believe that the reason is that the sealing ring of the main cylinder is damaged or overturned, there is no brake fluid in the main cylinder, no brake pressure, and the brake pipeline is seriously broken or the pipeline joint is disconnected. Replace the damaged sealing ring, add sufficient brake fluid to the standard value, drain the air in the oil circuit, and replace the damaged brake pipeline.
變速箱空檔或掛檔后，變速箱壓力低，整機行走無力？ 變速箱內變速箱油量不足，變速箱油底殼濾清器堵塞，行走泵損壞，容積效率低，減壓閥或進油壓力閥調整不當，吸油 行走泵管路老化或嚴重彎曲。 怠速時在變速箱內加足液壓油至油標中心，更換行走泵，更換或清洗濾網，重新調整壓力達到規定范圍，更換油管。
After the gearbox is in neutral or mounted, the gearbox pressure is low and the whole machine is weak. There is insufficient oil in the transmission box, the filter of the gearbox oil pan is blocked, the traveling pump is damaged, the volume efficiency is low, the pressure reducing valve or the oil inlet pressure valve is improperly adjusted, and the oil suction traveling pump pipeline is aging or seriously bent. When idle, add enough hydraulic oil in the gearbox to the center of the oil mark, replace the walking pump, replace or clean the filter screen, adjust the pressure to reach the specified range, and replace the oil pipe.
裝載機租賃維修有四大問題要了解，以上便是詳解，如果您發現出現的故障您找不到原因解決不了，這個時候就要馬上找專業的維修人員來，以免造成二次損壞。更多內容就來網站id888.com.cn咨詢吧。
Loader rental maintenance has four problems to understand, the above is a detailed solution, if you find the fault you can not find the reason to solve, this time to find professional maintenance personnel immediately, so as not to cause secondary damage. For more information, visit id888.com.cn.
公司地址：濟南市商河縣賈莊鎮民營經濟創業園
公司名稱:永誠廣建公路材料（山東）有限公司 
備案號：